Response SA1 E Betriebsanleitung PDF herunterladen (Seite 22)

PIR Movement Detector false alarming.

1. Ensure that the detector is not pointing at a source

of heat or a moving object.

2. Ensure that the detector is not mounted above a

radiator or heater.

3. Ensure that the detector is not facing a window or in

direct sunlight.

4. Ensure that the detector is not in a draughty area.

5. Sensitivity set too HIGH – reset to LOW sensitivity,

(i.e. DIP 5 of SW3 OFF).

PIR Movement Detector not detecting a person’s

movement.

1. Ensure the battery clip is securely connected.

2. Ensure ‘House Code’ is correctly set to the same

code as all other system devices.

3. Sensitivity set too LOW – reset to HIGH sensitivity,

(i.e. DIP 5 of SW3 ON).

4. Ensure DIP switches 1, 2 and 3 of SW3 are

correctly set, (i.e. 1=ON, 2=ON, and 3=OFF).

5. Ensure that detector is mounted the correct way up,

(i.e. with detection window at the bottom).

6. Ensure that the detector is mounted at the correct

height, (i.e. 2 - 2.5 metres).

7. Allow up to 3 minutes for detector to stabilize and

become fully operational. Leave the area for this

period.

8. Ensure detector is within effective radio range of

the Siren and is not mounted close to metal objects

which may interfere with the radio transmission.

PIR Movement Detector LED ashes on detection

of movement, (device in Normal Operation mode).

1. Ensure that the detector is congured for normal

operation, (i.e. DIP switch 4 of SW3 is OFF).

2. Low battery - Replace battery.

Magnetic Contact Detector not working.

1. Ensure that Magnet is correctly positioned in

relation to Detector and that the gap between

magnet and detector is less than 10mm.

2. Ensure batteries are tted with correct polarity.

3. Ensure battery holder connections are making good

contact with the batteries and PCB (Circuit board).

4. Ensure ‘House Code’ is correctly set to the same

code as all other system devices.

5. Ensure DIP switches 9, 10 and 11 are correctly set,

(i.e. 9=ON, 10=ON, and 11=OFF).

6. If there is no additional wired Magnetic Contact

connected ensure jumper link is tted.

7. If an additional wired Magnetic Contact is

connected:

a. Ensure jumper link is removed.

b. Check that both contacts are closed.

c. Check that additional contact is correctly wired.

Note: If a wired contact is used, both protected

doors / windows must be closed when the system

is armed (otherwise neither door/window will be

protected).

8. Ensure detector is within effective radio range of

the Siren and is not mounted close to metal objects

which may interfere with the radio transmission.

Magnetic Contact Detector false alarming.

1. Ensure that Magnet is correctly positioned in

relation to Detector.

2. Ensure that gap between Magnet and Detector is

less than 10mm.

3. Tamper switch below battery cover not depressed

– check battery cover is tted correctly and that

xing lugs are not broken.

LED on Magnetic Contact Detector illuminating

when door or window is opened.

1. Low battery - replace batteries.

HELPLINE

If you have any problems with your alarm, please

call the Helpline on:

01268 563273

(Lines open 9.00am to 5.00pm, Monday to Friday)

1 2 ... 17 18 19 20 21 22 23 24

Kommentare zu diesen Handbüchern

Keine Kommentare

Response SA1 E Betriebsanleitung Seite 22

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme Response SA1 E